Harbor Freight Tools Marine Safety Devices 96291 User Manual

12 volt “oooga” horn  
96291  
Model  
asseMbly and operation instructions  
Due to continuing improvements, actual product may differ slightly from the product described herein.  
®
3491 Mission Oaks Blvd., Camarillo, CA 93011  
visit our website at: http://www.harborfreight.com  
to prevent serious injury, read and understand  
all warnings and instructions before use.  
©
®
Copyright 2007 by Harbor Freight Tools . All rights reserved. No portion of this  
manual or any artwork contained herein may be reproduced in any shape or form  
without the express written consent of Harbor Freight Tools.  
for technical questions or replacement parts, please call 1-800-444-3353.  
 
6.  
store idle equipment out of reach of children and other untrained persons.  
Tools are dangerous in the hands of untrained users.  
7.  
check for breakage of parts and any other condition that may affect the oooga  
horns operation. If damaged, have the tool serviced before using.  
8.  
service must be performed only by qualified repair personnel. Service or  
maintenance performed by unqualified personnel could result in a risk of injury.  
9.  
Maintain labels and nameplates on the oooga horn. These carry important infor-  
mation. If unreadable or missing, contact Harbor Freight Tools for a replacement.  
10.  
warning: the brass components of this product contain lead, a chemical  
known to the state of california to cause birth defects (or other reproductive  
harm). (California Health & Safety code § 25249.5, et seq.)  
11.  
12.  
exposure to noise levels over 85 db is hazardous to hearing. Always wear  
ANSI approved hearing protection when operating the Oooga Horn. Never use  
Horn in close proximity to people or animals, as the decibel level may cause hear-  
ing damage.  
before using the oooga horn, check and comply with local standards for  
noise pollution levels.  
unpacking  
1.  
when unpacking, check to make sure that the item is intact and undamaged.  
If any parts are missing or broken, please call Harbor Freight Tools at the number  
shown on the cover of this manual as soon as possible.  
asseMbly instructions  
caution: Installation should be completed by a qualified technician.  
1.  
2.  
3.  
Before attempting installation of the Oooga Horn, turn off the ignition, shift the gear  
into park (for automatic transmissions) or reverse (for manual). Remove the car  
keys from the ignition switch and allow the engine to cool. Place wheel chocks on  
both sides of at least 2 wheels. Disconnect the vehicle’s battery. Make sure the  
engine and engine compartment are cool before beginning work.  
Lift the vehicle hood and find a suitable location to mount the Oooga Horn (1). This  
location must shelter the Oooga Horn and Compressor from incoming rain, road  
water, and mud splash from under the vehicle. Do not mount the Horn near hot  
engine components or where it may come into direct contact with hot surfaces or  
any moving parts.  
Mount the Oooga Horn to the vehicle’s chassis using the Nut and Bolt (2). The Oooga  
Horn (1) should be pointing forward and slightly down for maximum efficiency. A  
SKU 96291  
for technical questions, please call 1-800-444-3353.  
Page 3  
 
hole may need to be drilled in the chassis frame to accomplish this. Before drilling  
the hole, make sure the drill’s path will not come in contact with hidden wiring or  
any other obstructions or vehicle components. Tighten the Nut securely.  
4.  
5.  
Mount the Electric Relay (not included), as shown in the Wiring Diagrams, to the  
chassis frame near the Oooga Horn using a Bolt and Nut (not included). Tighten  
securely.  
Make the connections to the Oooga Horn (1) and the Electric Relay (not included)  
as shown on the Mounting and Wiring Diagrams. Always use terminal connectors  
(not included) on all connections. Connect the terminal on the Electric Relay to a  
30A fused circuit.  
note: Most vehicles use a negative ground, but some vehicles employ a positive ground. If  
this is the case, refer to Positive Ground Wiring Diagram. Pay attention to polarity.  
negative ground wiring diagram  
electric relay  
87  
pushbutton horn switch  
88  
85  
not included  
51  
30  
30 a  
+12 vdc  
connection is to the line positive  
“+” point of the original horn  
existing vehicle fused circuit  
REV 08a  
SKU 96291  
for technical questions, please call 1-800-444-3353.  
Page 4  
 
positive ground wiring diagram  
+12 vdc  
electric relay  
87  
pushbutton horn switch  
85  
88  
not included  
51  
30  
30 a  
-12 vdc  
connection is to the line positive  
“+” point of the original horn  
existing vehicle fused circuit  
SKU 96291  
for technical questions, please call 1-800-444-3353.  
Page 5  
 
inspection, Maintenance, and cleaning  
1.  
2.  
warning! Make sure the ignition of the vehicle is in the “OFF” position and  
that the tool is disconnected from the electrical outlet before performing any inspec-  
tion, maintenance, or cleaning procedures.  
BEFORE EACH USE, inspect the general condition of the tool. Check for loose  
screws, misalignment or binding of moving parts, cracked or broken parts, damaged  
electrical wiring, and any other condition that may affect its safe operation. If abnor-  
mal noise or vibration occurs, have the problem corrected before further use. Do  
not use damaged equipment. PLEASE READ THE FOLLOWING CAREFULLY  
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEM-  
BLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER  
OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER  
THAT HE OR SHE IS qUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR  
SHE IS qUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER  
AND/OR DISTRIBUTOR ExPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS  
SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE  
BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS  
TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS  
OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.  
parts list  
part  
1
description  
Horn/Compressor  
Nut & Bolt  
1
2
2
record products serial number here:  
note: If product has no serial number, record month and year of purchase instead.  
note: Some parts are listed and shown for illustration purposes only, and are not available individually as  
replacement parts.  
SKU 96291  
for technical questions, please call 1-800-444-3353.  
Page 6  
 

Graco High Chair PD223741A User Manual
Haier Dishwasher HDW12 SFE1 User Manual
Harman Kardon GPS Receiver GPS 200GSEC User Manual
Hotpoint Electric Pressure Cooker C220E User Manual
HP Hewlett Packard Projector mp3320 User Manual
HP Hewlett Packard Switch A7340 96002 User Manual
HP Hewlett Packard Work Light 6269A User Manual
HTC Cell Phone BLAC100 User Manual
Husqvarna Trimmer 965966701 User Manual
IBM Network Card 59P5712 User Manual