Harbor Freight Tools Kitchen Utensil 66473 User Manual

heaVY dutY  
French FrY  
cutter  
66473  
InstructIons and precautIons  
Visit our website at: http://www.harborfreight.com  
saVe these InstructIons. read all  
precautIons and InstructIons.  
©
®
Copyright 2009 by Harbor Freight Tools . All rights reserved. No portion of this document or any artwork contained  
herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. Diagrams  
within this document may not be drawn proportionally. Due to continuing improvements, actual product may differ  
slightly from the product described herein. Tools required for assembly and service may not be included.  
For technical questions or replacement parts, please call 1-800-444-3353.  
missing or broken, please call Harbor Freight Tools  
at the number shown on the cover of this document  
as soon as possible.  
specIFIcatIons  
Two sizes of Cutters and Pushing Blocks are  
included in this set. This tool may be wall or table  
top mounted. This tool may be disassembled for  
Important saFetY  
cleaning.  
Cutter Frame Size: 4-5/8”W x 4-5/8”H x 11/16”T  
InFormatIon  
1.  
2.  
3.  
4.  
This is a cutting device. Do not place hand  
near Pushing Block and Cutter.  
Do not hold vegetable or any object in place  
during cutting operation.  
To prevent pinch injury, keep hands clear of  
Lever (1) and Push Rods (9) at all times.  
Assemble and use according to these  
instructions only. Improper assembly or use  
can create hazards.  
5.  
Wear ANSI-approved safety goggles and  
heavy-duty work gloves during assembly.  
6.  
7.  
Keep assembly and use area clean and well lit.  
unpackIng  
When unpacking, check to make sure that  
the item is intact and undamaged. If any parts are  
Keep bystanders out of the area during  
assembly and use.  
Revised Manual 09j  
 
Block and Cutting Frame will damage the  
tool.  
operatIon  
1.  
2.  
Pull the Lever (1) back, which will pull the  
Push Block back from the Cutting Frame.  
Place a bowl beneath the End Support (2)  
to catch the cut french fries as they are  
produced.  
3.  
4.  
Place the potato or vegetable to be cut in the  
Food Tray (6). Align the vegetable roughly  
with the center of the Cutting Frame.  
Press the Lever (1) forward. The Push Block  
will press the vegetable through the Cutting  
Frame. Stop pressing the Lever forward once  
the vegetable has been cut.  
Push Block Latches  
4.  
To remove the Cutting Frame (10 or 12),  
remove the four wing nuts holding it in place.  
WARNING: Handle the Cutting Frame by the  
outer edge only. The blades are sharp and  
can cause injury if handled. The blades are  
not removable from the Cutting Frame.  
cleanIng  
1.  
Remove both the Cutting Frame (10 or 12)  
and Push Block (11 or 13).  
2.  
3.  
Lift Food Tray (6) out of tool.  
5.  
6.  
To replace the Push Block, place it against  
Block Plate A (4) with hooks protruding  
through holes in Block Plate A. Then fix it in  
place with the two swivel latches.  
Wash Cutting Frame, Push Block and Food  
Tray in dishwasher, or by hand using hot  
water and detergent.  
4.  
Wipe off the rest of the tool using a clean  
damp cloth with light detergent. Wipe it dry  
after cleaning.  
To replace the Cutting Frame, position it on  
the end of the End Support (2) and attach it  
with the Wing Nuts.  
Wing Nut (19)  
Wing Nuts(15)  
note: Always use the Push Blocks and Cutting  
Frames in matched pairs. Using mismatched  
SKU 66473  
For technical questions, please call 1-800-444-3353.  
Page 3  
 
1
record serial number here:  
8
11  
note:If product has no serial number, record  
16  
month and year of purchase instead.  
5
note:Some parts are listed and shown for  
illustration purposes only, and are not  
available individually as replacement parts.  
7
4
9
10  
3
2
19  
6
18  
17  
15  
parts lIst & assemBlY  
dIagram  
part  
description  
Qty.  
1
Lever  
1
2
End Support (Stand A)  
Lever Support (Stand B)  
Block Plate A  
1
3
1
please read the FolloWIng  
4
1
careFullY  
5
Block Plate B  
1
THE MANUFACTURER AND/oR DISTRIBUToR HAS  
PRoVIDED THE PARTS LIST AND ASSEMBLy DIAGRAM IN  
THIS DoCUMENT AS A REFERENCE TooL oNLy. NEITHER  
THE MANUFACTURER oR DISTRIBUToR MAKES ANy  
REPRESENTATIoN oR WARRANTy oF ANy KIND To THE  
BUyER THAT HE oR SHE IS qUALIFIED To MAKE ANy  
REPAIRS To THE PRoDUCT, oR THAT HE oR SHE IS  
qUALIFIED To REPLACE ANy PARTS oF THE PRoDUCT.  
IN FACT, THE MANUFACTURER AND/oR DISTRIBUToR  
ExPRESSLy STATES THAT ALL REPAIRS AND PARTS  
REPLACEMENTS SHoULD BE UNDERTAKEN By CERTIFIED  
AND LICENSED TECHNICIANS, AND NoT By THE BUyER.  
THE BUyER ASSUMES ALL RISK AND LIABILITy ARISING  
oUT oF HIS oR HER REPAIRS To THE oRIGINAL PRoDUCT  
oR REPLACEMENT PARTS THERETo, oR ARISING oUT  
oF HIS oR HER INSTALLATIoN oF REPLACEMENT PARTS  
THERETo.  
6
Food Tray  
1
7
Support Rods with Wing Nuts  
D12 x L27.4 cm  
3
8
Lever Rods D7 x L37 cm  
Push Rods D7 x L22 cm  
Cutting Frame 64 Holes  
Push Block 64 Holes  
2
2
1
1
1
1
3
1
1
1
1
9
10  
11  
12  
13  
15  
16  
17  
18  
19  
Cutting Frame 36 Holes(not shown)  
Push Block 36 Holes(not shown)  
Wing Nuts 5/16”  
Cutting Frame Bolt  
Axle Bolt and Nut set  
Push Rod Bolt and Nut set  
Wing Nut M5  
REV 09c, 09h, 09j  
SKU 66473  
For technical questions, please call 1-800-444-3353.  
Page 4  
 

Grizzly Grinder H8218 User Manual
Hamilton Beach Mixer Drink Mixer User Manual
Hamilton Beach Slow Cooker 33139 User Manual
Harbor Freight Tools Portable Generator 91377 User Manual
Honeywell Switch BZG H User Manual
Hotpoint Washer WMF 740 P G A K X User Manual
HP Hewlett Packard Network Cables 8505A User Manual
HP Hewlett Packard Scanner 2200c User Manual
IBM Computer Drive 73P3279 User Manual
IKEA Oven CG3 User Manual