Harbor Freight Tools Dust Collector 93601 User Manual

DUST COLLECTOR  
ACCESSORY KIT  
93601  
ASSEMBLY & OPERATING INSTRUCTIONS  
Due to continuing improvement, actual product may differ slightly from product described herein.  
®
3491 Mission Oaks Blvd., Camarillo, CA 93011  
Copyright© 2005 by Harbor Freight Tools®. All rights reserved. No portion of this manual or  
any artwork contained herein may be reproduced in any shape or form without the  
express written consent of Harbor Freight Tools.  
For technical questions and replacement parts please call 1-800-444-3353.  
 
10.  
Always check hardware and assembled parts after assembling. All connections should  
be tight and hardware tightened.  
11.  
12.  
Caution: Avoid sharp edges during use and assembly.  
Beware of operating the power tool in explosive atmospheres, such as in the  
presence of flammable liquids, gases, or sawdust. Electrical products create sparks  
which may ignite sawdust released from the Dust Collector, as well as other dust and fumes.  
13.  
Carefully inspect the condition of the accessory before use and check the accessory  
continually during use. If any damage is noted, stop immediately and replace the  
accessory with an undamaged one. Harbor Freight Tools cannot be held responsible  
for damage caused by using a damaged accessory on this product.  
14.  
15.  
Keep the hoses away from sharp objects and excessive heat.  
Make sure to read and understand all instructions and safety precautions, as outlined in the  
manufacturer’s manual of the power equipment to which the Dust Collector Accessory Kit  
will be attached.  
WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other  
construction activites, contain chemicals known [to the State of California] to cause cancer,  
birth defects or other reproductive harm. some examples of these chemicals are:  
Lead from lead-based paints  
Crystalline silica from bricks and cement or other masonry products  
Arsenic and chromium from chemically treated lumber  
Your risk from these exposures varies, depending on how often you do this type of work. To  
reduce your exposure to these chemicals: work in a well ventilated area, and work with  
approved safety equipment, such as those dust masks that are specially designed to filter  
out microscopic particles. (California Health & Safety Code 25249.5, et seq. )  
Warning:  
The warnings, cautions, and instructions discussed in this instruction manual cannot  
cover all possible conditions and situations that may occur. It must be understood by  
the operator that common sense and caution are factors which cannot be built into  
this product, but must be supplied by the operator.  
Unpacking  
When unpacking your Dust Collector Accessory Kit, check to make sure all parts listed on page 5  
are included. If any parts are missing or broken, please call HARBOR FREIGHT TOOLS at  
1-800-444-3353.  
Product Overview  
The Dust Collector Accessory Kit is designed to be attached to one or two power tools, and is used  
for the collection of wood dust, wood chips, sand, and other light debris. The Dust Collector  
Accessory Kit may be attached to table saws, band saws, sanders, router tables, shapers, jointers,  
and a variety of dust collecting machines all having a 4” dust port. Due to the wide diversity of  
power machinery to which the Dust Collector Accessory Kit may be attached, it is recommended  
that only a qualified technician perform the assembly procedure.  
SKU 93601  
For technical questions please call 1-800-444-3353.  
Page 3  
 
Assembly  
1.  
2.  
Though the Dust Collector Accessory Kit is designed to offer a wide variety of applications, the  
following illustration depicts a typical assembly method to hook-up one power equipment tool  
and two power equipment tools-see Figure 1 below.  
Note: The Dust Collector Accessory Kit is designed to be attached to stationary power  
equipment tools and dust collectors having 4” diameter dust ports. Depending on the  
diameter of the dust port of your power equipment tools and dust collector, it may be  
necessary to attach size adapters (not included) to ensure a proper fit.  
Figure 1-To Attach to One or Two Power Tools  
Attaching to One Power Tool  
Jointer Hood (6” square) (3)  
4” Diameter Blast Gate (2)  
or  
4”Wire Hose Clamp (6)  
Table Saw Dust Hood (12square) (5)  
Dust  
Port  
Dust  
Port  
Dust  
Collector  
Flexible Hose (1)  
Attaching to Two Power Tools  
“Y” Fitting (4)  
Power  
Tool  
Power  
Tool  
3.  
4.  
5.  
Check the length of Flexible Hose (1) needed to set up the Dust Collector Accessory Kit with  
your power tool. It may be necessary to cut the Flexible Hose (1). To cut the Flexible  
Hose (1), cut the plastic on the hose in a straight line between one coil of wire. Use a tin  
snip or wire cutter to cut the coil inside the hose.  
Place a Wire Hose Clamp (6) over the Flexible Hose. Slide the Flexible Hose (1) onto the  
dust port. Slide the Wire Hose Clamp (6) so that it sits on both a section of Flexible Hose (1)  
and the dust port. Thread down the screw on the Wire Hose Clamp (6) until the Flexible  
Hose (1) is tight on the dust port.  
Open and close the Blast Gate (2) to control the air flow from the Power Tool(s) to the dust  
collector. When this kit is attached to 2 power tools, always close the Blast Gate (2) of an  
unused dust collector hose.  
SKU 93601  
For technical questions please call 1-800-444-3353.  
Page 4  
 
Inspection, Maintenance and Cleaning  
1.  
2.  
CAUTION: Prior to performing any inspection, maintenance, or cleaning of the Dust  
Collector Accessory Kit, make sure to turn OFF and then disconnect the power tool from the  
outlet.  
BEFORE EACH USE, inspect the general condition of the Dust Collector Accessory Kit.  
Check for loose connections, misalignment or binding of moving parts, cracked, torn, or  
broken parts, and any other condition that may affect its safe operation. If abnormal noise or  
vibration occurs, have the problem corrected before further use. Do not use damaged  
equipment.  
3.  
4.  
DAILY: With a soft brush, cloth, or vacuum, remove all debris from the Dust  
Collector Accessory Kit. If necessary, you may use a mild detergent.  
Clean the hoses periodically by standing it on end and tapping it to remove dust and debris.  
PLEASE READ THE FOLLOWING CAREFULLY  
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A REFERENCE  
TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY  
KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS  
QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY  
STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED  
TECHNICIANS AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER  
REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION  
OF REPLACEMENT PARTS THERETO.  
Parts List  
Part #  
Description  
Quantity  
1
2
3
4
5
6
Flexible Hose, 4” x 10’  
Blast Gate-4” x 4”  
Jointer Hood-6”  
“Y” Fitting-4” x 4” x 4”  
Table Saw Dust Hood 12” x 12” 1  
2
2
2
1
Wire Hose Clamp  
10  
Parts Diagram  
1
6
2
5
3
4
SKU 93601  
For technical questions please call 1-800-444-3353.  
Page 5  
 

Groupe SEB USA T FAL Electric Pressure Cooker Pressure Cooker User Manual
Haier Freezer HUM013EA User Manual
Hasbro Games Giggle Game User Manual
Hasbro Motorized Toy Car 73988 User Manual
Hotpoint Cooktop HL500G User Manual
Hotpoint Dishwasher HDA1100ZWH User Manual
HP Hewlett Packard Computer Monitor CQ1859 User Manual
Humax Flat Panel Television LGB 19DTT User Manual
Hypertec Carrying Case N8938MHY User Manual
Hypertec Carrying Case N16298MHY User Manual