Harbor Freight Tools Door 95588 User Manual

3 Piece decorative  
solar light set  
Model 95588  
asseMbly and oPeration instructions  
Due to continuing improvements, actual product may differ slightly from the product described herein.  
®
3491 Mission Oaks Blvd., Camarillo, CA 93011  
visit our website at: http://www.harborfreight.com  
to Prevent serious injury, read and understand  
all warnings and instructions before use.  
©
®
Copyright 2006 by Harbor Freight Tools . All rights reserved. No portion of this  
manual or any artwork contained herein may be reproduced in any shape or form  
without the express written consent of Harbor Freight Tools.  
for technical questions or replacement parts, please call 1-800-444-3353.  
 
5.  
6.  
use safety equipment. always wear eye protection. Always wear ANSI-approved  
safety goggles when performing maintenance on this product.  
do not force the product. use the correct product for your application. The  
correct product will do the job better and safer at the rate for which it is designed. Do  
not force the product and do not use it for a purpose for which it is not intended.  
7.  
do not use this product if the Power switch does not turn it on or off. Any  
product that cannot be controlled with the Power Switch is dangerous and must be  
replaced.  
8.  
9.  
store idle products out of reach of children and other untrained persons. This  
product is dangerous in the hands of untrained users.  
use only accessories that are recommended by the manufacturer for your  
model. Accessories that may be suitable for one product may become hazardous  
when used on another product.  
10.  
when servicing a product, use only identical replacement parts. follow  
instructions in the “Inspection, Maintenance, And Cleaning” section of this  
manual. Use of unauthorized parts or failure to follow maintenance instructions  
may create a risk of electric shock or injury.  
11.  
12.  
13.  
Maintain labels and nameplates on the product. These carry important informa-  
tion. If unreadable or missing, contact Harbor Freight Tools for a replacement.  
Maintain a safe working environment. Make sure there is adequate surrounding  
workspace. Do not use this product in a damp or wet location.  
People with pacemakers should consult their physician(s) before using this  
product. Electromagnetic fields in close proximity to a heart pacemaker could cause  
interference to or failure of the pacemaker. In addition, people with pacemakers  
should adhere to the following:  
Avoid operating power tools alone.  
Don’t use a power tool with the power switch locked on.  
If powered via a power cord be certain that the tool is properly grounded.A ground  
fault interrupt (GFCI) system is also a good precaution. This inexpensive device is  
a good safety measure because it prevents a sustained electrical shock.  
Properly maintain and inspect all tools before use to avoid electrical shock.  
14.  
15.  
Keep the solar Panel free of dirt, dust and grime. dust covering the solar  
Panel will block out sunlight causing a decrease or stoppage of efficiency in  
recharging the battery.  
warning: nicad batteries must be disposed of properly. Do not incinerate.  
The battery may burst, causing personal injury and/or property damage. Contact  
your local hazardous waste disposal authority for proper disposal.  
SKU 95588  
for technical questions, please call 1-800-444-3353.  
Page 3  
 
unPacKing  
When unpacking, check to make sure that the item is intact and undamaged. If any  
parts are missing or broken, please call Harbor Freight Tools at the number shown on the  
cover of this manual as soon as possible.  
asseMbly and oPerating instructions  
note: For additional information regarding the parts listed in the following pages, refer to  
the Assembly Diagram near the end of this manual.  
1.  
2.  
warning! Make sure the Power Switch of the product is in its “OFF” position  
before making any adjustments to the product.  
Decide where you want to place the Solar Light Set. Choose a location that receives  
full, direct sunlight a minimum of six hours a day. The location should not be near  
nighttime light sources such as porch lights or streetlights as this will cause the  
Solar Light Set to remain off.  
3.  
4.  
5.  
The Solar Light Set will need to charge for at least twelve hours before using it for  
the first time. Allow to charge for two sunny days before the Solar Light Set is fully  
charged. During initial charging, set the switch to “Off”.  
Located underneath the Battery Cover (9) is a Auto/Off Switch (7). The Switch can  
be set to either “Auto” or “Off”. Set the Auto/Off Switch to “Auto.-see Figure 1 and  
Parts Diagram.  
Moving the Auto/Off Switch (7) to “Auto” will automatically turn on the Solar Light  
during the night. After the initial charge is set, check to see that the Light (2) is on  
by viewing the light at night or in a dark location. If the Light (2) is not lit, check the  
position of the “Auto” Switch.  
6.  
Note: During the day, the Solar Panel converts sunlight into electricity, recharging  
the battery. The amount of light the Solar Panel receives depends on placement  
of the Solar Light, geographic location and weather. If the weather is cloudy and  
the panel did not receive a full charge, the Solar Garden Light may not achieve the  
full hours of operating time. It will catch up on its own after two to three days of full  
sun.  
7.  
8.  
Set the Hummingbird, Dragonfly or Butterfly onto the Top Tube (3). Slide the Top  
Tube (3), into the Bottom Tube (4). Slide the Stake (5) onto the Bottom Tube (4).  
Push the Stake (5) directly into the ground. Make certain that the path of the Stake  
(5) is clear of lines, cables and conduits.  
SKU 95588  
for technical questions, please call 1-800-444-3353.  
Page 4  
 
rePlacing the batteries  
1.  
2.  
It is recommended that you replace the battery every 12 months.  
Unscrew the screws from underneath the Battery Cover (9) and remove it from the  
Solar Panel (1)-see Figure 1.  
3.  
4.  
Remove and properly recycle the old battery. Make certain that the new battery is  
Ni-Cd ( “AA”, 1.2V, 600 mAh) rechargeable.  
Install the new battery into the Battery Compartment. Make certain that the battery  
is placed according to the correct polarity-see Figure 1.  
Figure 1  
Solar Panel  
Auto/Off Switch (7)  
Battery Cover  
(9)  
Battery (6)  
5.  
1.  
Replace the cover and screw it back into place.  
insPection, Maintenance and cleaning  
Clean regularly with a damp towel. Do not use any type of solvent for cleaning. Do  
not put too much pressure on the Light, Solar Panel or accessories while cleaning.  
Dry thoroughly.  
2.  
3.  
warning! Make sure the Auto/Off Switch is in its “OFF” position before per-  
forming any inspection, maintenance, or cleaning procedures.  
before each use, inspect the general condition of the Solar Light Set. Check  
for loose screws, cracked or broken parts, damaged electrical wiring, and any other  
condition that may affect its safe operation. do not use damaged equipment.  
SKU 95588  
for technical questions, please call 1-800-444-3353.  
Page 5  
 
troubleshooting  
Possible causes  
Problem  
Probable solutions  
Light will not go on  
1. Auto/Off Switch (7) not set to  
“Auto”.  
1. Check position of Auto/Off Switch  
2. Make certain that Solar Panel has  
direct access to sunlight. Allow one  
to two days for a full charge  
2. Battery not allowed time for  
recharging via Solar Panel  
3. Solar Light is set near nighttime  
light sources such as porch lights  
or street lights  
3. Move Solar Light or change Solar  
Panel position  
4. Solar Panel is dirty and covered  
with dirt or dust  
4. Clean Solar Panel with a soft cloth  
Parts list  
Part  
1
description  
Solar Panel  
Q’ty Part  
description  
Battery  
Q’ty  
3
3
6
2
Butterfly, Dragon Fly,  
Hummingbird  
1 of  
each  
7
Auto/Off Switch  
3
3
4
5
Top Tube  
Bottom Tube  
Stake  
3
3
3
8
9
Cover Screw  
Battery Cover  
6
3
Parts and asseMbly diagraM  
1
7
9
6
8
SKU 95588  
for technical questions, please call 1-800-444-3353.  
Page 6  
 
Parts and asseMbly diagraM (cont’d)  
4
5
3
1
2
Please read the following carefully  
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEM-  
BLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER  
OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER  
THAT HE OR SHE IS qUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR  
SHE IS qUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER  
AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS  
SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE  
BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS  
TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS  
OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.  
SKU 95588  
for technical questions, please call 1-800-444-3353.  
Page 7  
 

Hansol Multitech Computer Monitor B19BL User Manual
Harbor Freight Tools Air Compressor 93271 User Manual
Harbor Freight Tools Wheelchair 45735 User Manual
Healthrider Treadmill HRTL08980 User Manual
Heat Controller Air Conditioner BD 101 User Manual
Honeywell Video Gaming Accessories wt6500 User Manual
Hotpoint Oven SE87PX User Manual
Hotpoint Washer WMYL 6351 User Manual
Husqvarna Chainsaw T425 User Manual
Hypertec Mouse KYB LIGHTNING 01HY User Manual